SEARCH WHAT YOU WANT
PPS500A
The design system consists of ternary lithium 8s5p battery protection board, DC charging circuit, MCU control circuit, inverter circuit and LCD screen. Inverter 500W pure sine wave AC220V/50Hz, subject to pure resistance load, DC12V/ 10A, USB QC3 0,TYPE-C PD3. 0 lt is suitable for camping, emergency communication, medical rescue, fire rescue and other fields.
The design system consists of ternary lithium 8s5p battery protection board, DC charging circuit, MCU control circuit, inverter circuit and LCD screen. Inverter 500W pure sine wave AC220V/50Hz, subject to pure resistance load, DC12V/ 10A, USB QC3 0,TYPE-C PD3. 0 lt is suitable for camping, emergency communication, medical rescue, fire rescue and other fields.
Previous page: No more
Next page: PPS500B
Product Details
Attention
● Please follow the manuals.
● Please leave at least 5cm for the air vent. In case the device over-heating.
● The device will automatically shut offff when the electricity of device is not enough or the discharging device watt is bigger than 500W, or in high temperature condition.
● Please donʼt charge and discharge at same time.
● If you donʼt use this device for a long time. The electricity may runs out. Please charge this device every 6 months.
● When loading some big watt products. If its instantaneous power is over 1000W. the device will automatically protect itself. It will turn offff the output.
● Please make sure the loading product need no more than 1000W of instantaneous power.
● Please donʼt use this device under some extremely condition, eg: flflammable or corrosive condition.
● If you drop the device into water by accident.
● Please send back it to where you purchased. We will take care it. If the device damaged by wrong use.
● We may charge accordingly.
Precautions for Product Operation
● Strictly follow the operation steps of the product.
● For the heat dissipation space of the product, 5cm space is reserved around the product to make the heat dissipation convective.
● When the power of the product is insufficient, the load power exceeds the rated power or the ambient temperature is too high, the product will automatically start the protection function and turn off the output.
● For power charging, it is recommended to charge without load.
● If the power supply is not used for a long time, the power supply itself will be exhausted. Please make sure to charge it every 6 months.
● It is forbidden to use this product in flammable, explosive and corrosive gas environment such as gasoline and gas.
● If the product is accidentally flooded or invaded by other foreign substances, please send it to the Distribution Office for testing and treatment as soon as possible to ensure the safe use of the product. If it is caused by abnormal use, the company will charge for treatment according to the actual situation.
Product Scenarios
Specification
|
Model |
PPS500A |
|
|
Capacity |
2800m Ah * 6 Series 8 parallel 134400m A H |
|
|
Cell |
18650/2800mAh 3C |
|
|
Battery Power |
497WH |
|
|
AC Power |
Sine wave AC 500W 220V / 50H z |
|
|
AC Peak V alue |
1000W peak maintenance time < 50ms |
|
|
Conversion Eff i ciency |
85% ≤ |
|
|
Class |
Project |
Specifications |
|
IN TPU T |
D C input |
DC5521 12-24V -5A |
|
AC OU T 220V |
AC output voltage |
1 A C socket A C220V ± 5% |
|
AC output power |
500W |
|
|
AC output over power protection |
About 550W |
|
|
AC output waveform |
Correction wave |
|
|
AC output peak |
1000W peak maintenance time < 50ms |
|
|
Frequency |
50Hz |
|
|
USB output port |
U sb1 output |
QC3.0 M A X 12V /1.5A |
|
U SB 2 output |
QC3.0 M A X 12V /1.5A |
|
|
TY PE-C1 output |
PD /QC3.0 M A X 12V /1.5A |
|
|
DC12V output |
DC1 DC2 output |
12V /10A M A X |
|
Type-C output / input |
TY PE-C2 |
Pd60w output |
|
Electric core |
type |
Ternary l i thium cell 18650 / 2800mah |
|
capacity |
134400mAH （6S8P） |
|
|
power |
497WH |
|
|
cycle l i fe |
M ore than 1000 times |
|
|
Charging parameters |
|
D C 12-24V /5A |
|
Charging time |
6-7H |
Charge f rom 0% to 100% (automatic cut-off) |
|
Full voltage |
25.2V ± 0.1V |
The battery is charged to the voltage at automatic cut-off |
|
LCD display |
D i splay the power, charge and stop charge status |
The power column f lashes, PD + in, and the power column i s always on |
|
D C, A C and inverter status |
Switch status of U SB QC 3.0 and A C |
|
|
Boot static |
|
<10W |
|
Protection function |
|
Short ci rcuit, overload, overtemperature, overvoltage, overcurrent, undervoltage, etc |
|
I nverter over temperature protection |
Over temperature protection |
≥ 85℃ |
|
Over temperature recovery |
≤ 70℃ |
|
Attention
● Please follow the manuals.
● Please leave at least 5cm for the air vent. In case the device over-heating.
● The device will automatically shut offff when the electricity of device is not enough or the discharging device watt is bigger than 500W, or in high temperature condition.
● Please donʼt charge and discharge at same time.
● If you donʼt use this device for a long time. The electricity may runs out. Please charge this device every 6 months.
● When loading some big watt products. If its instantaneous power is over 1000W. the device will automatically protect itself. It will turn offff the output.
● Please make sure the loading product need no more than 1000W of instantaneous power.
● Please donʼt use this device under some extremely condition, eg: flflammable or corrosive condition.
● If you drop the device into water by accident.
● Please send back it to where you purchased. We will take care it. If the device damaged by wrong use.
● We may charge accordingly.
Precautions for Product Operation
● Strictly follow the operation steps of the product.
● For the heat dissipation space of the product, 5cm space is reserved around the product to make the heat dissipation convective.
● When the power of the product is insufficient, the load power exceeds the rated power or the ambient temperature is too high, the product will automatically start the protection function and turn off the output.
● For power charging, it is recommended to charge without load.
● If the power supply is not used for a long time, the power supply itself will be exhausted. Please make sure to charge it every 6 months.
● It is forbidden to use this product in flammable, explosive and corrosive gas environment such as gasoline and gas.
● If the product is accidentally flooded or invaded by other foreign substances, please send it to the Distribution Office for testing and treatment as soon as possible to ensure the safe use of the product. If it is caused by abnormal use, the company will charge for treatment according to the actual situation.
Product Scenarios
Specification
|
Model |
PPS500A |
|
|
Capacity |
2800m Ah * 6 Series 8 parallel 134400m A H |
|
|
Cell |
18650/2800mAh 3C |
|
|
Battery Power |
497WH |
|
|
AC Power |
Sine wave AC 500W 220V / 50H z |
|
|
AC Peak V alue |
1000W peak maintenance time < 50ms |
|
|
Conversion Eff i ciency |
85% ≤ |
|
|
Class |
Project |
Specifications |
|
IN TPU T |
D C input |
DC5521 12-24V -5A |
|
AC OU T 220V |
AC output voltage |
1 A C socket A C220V ± 5% |
|
AC output power |
500W |
|
|
AC output over power protection |
About 550W |
|
|
AC output waveform |
Correction wave |
|
|
AC output peak |
1000W peak maintenance time < 50ms |
|
|
Frequency |
50Hz |
|
|
USB output port |
U sb1 output |
QC3.0 M A X 12V /1.5A |
|
U SB 2 output |
QC3.0 M A X 12V /1.5A |
|
|
TY PE-C1 output |
PD /QC3.0 M A X 12V /1.5A |
|
|
DC12V output |
DC1 DC2 output |
12V /10A M A X |
|
Type-C output / input |
TY PE-C2 |
Pd60w output |
|
Electric core |
type |
Ternary l i thium cell 18650 / 2800mah |
|
capacity |
134400mAH （6S8P） |
|
|
power |
497WH |
|
|
cycle l i fe |
M ore than 1000 times |
|
|
Charging parameters |
|
D C 12-24V /5A |
|
Charging time |
6-7H |
Charge f rom 0% to 100% (automatic cut-off) |
|
Full voltage |
25.2V ± 0.1V |
The battery is charged to the voltage at automatic cut-off |
|
LCD display |
D i splay the power, charge and stop charge status |
The power column f lashes, PD + in, and the power column i s always on |
|
D C, A C and inverter status |
Switch status of U SB QC 3.0 and A C |
|
|
Boot static |
|
<10W |
|
Protection function |
|
Short ci rcuit, overload, overtemperature, overvoltage, overcurrent, undervoltage, etc |
|
I nverter over temperature protection |
Over temperature protection |
≥ 85℃ |
|
Over temperature recovery |
≤ 70℃ |
|
Send us a Message
